[Voyage-linux] error in madwifi-tools

[Giorgio Ducci]

Hi Toth,

yes, I have kernel 2.6.8-486-voyage and madwifi-tools-20050726 and I have 
the same problem with the same card..WIth the previous madwifi-tools as you 
mention was fine for me, too. Who knows?
Cheers
>Dear Tse,
>
>The working version is the madwifi 20050105-1 which was included in the
>voyage0.1sarge version.
>
>The voyage-0.2pre1 use the kernel-image-2.6.8-486-voyage_2.0-2 and
>madwifi_20050712. This combination is useless for my card.
>
>I used the downloadable version from both dists and I changed nothing on
>them.
>
>Toth
>
>On Wed, 21 Sep 2005, Punky Tse wrote:
>
> > Toth,
> >
> > How old is your madwifi, or which kernel or voyage version you 
> used?  Please be more specific.
> >
> > Toth Szabolcs wrote:
> > > Hi !
> > >
> > > I have an Ubiquiti Networks SuperRange2 802.11b/g 400mW High Power 
> Atheros
> > > Wireless mini-pci card. I was able to set the Tx Power to 400wW width the
> > > old madwifi but with the new madwifi-tools I was unable to set the tx 
> power above 15-20dbm.
> > > I tired the following  but nothing changed:
> > > You can see that the Tx-Power hasn't gone above 15dBm however my card 
> can give 27dBm.
> > >
> > > wrap2c:~# iwconfig ath0 txpower auto
> > > wrap2c:~# iwconfig ath0
> > > ath0      IEEE 802.11b  ESSID:"ajka-air"
> > >           Mode:Master  Frequency:2.412 GHz  Access Point: 
> 00:15:6D:10:00:43
> > >           Bit Rate:0 kb/s   Tx-Power:12 dBm   Sensitivity=0/3
> > >           Retry:off   RTS thr:off   Fragment thr:off
> > >           Encryption key:off
> > >           Power Management:off
> > >           Link Quality=0/94  Signal level=-95 dBm  Noise level=-95 dBm
> > >           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> > >           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> > >
> > > wrap2c:~# iwconfig ath0 txpower fixed
> > > wrap2c:~# iwconfig ath0
> > > ath0      IEEE 802.11b  ESSID:"ajka-air"
> > >           Mode:Master  Frequency:2.412 GHz  Access Point: 
> 00:15:6D:10:00:43
> > >           Bit Rate:0 kb/s   Tx-Power=12 dBm   Sensitivity=0/3
> > >           Retry:off   RTS thr:off   Fragment thr:off
> > >           Encryption key:off
> > >           Power Management:off
> > >           Link Quality=0/94  Signal level=-95 dBm  Noise level=-95 dBm
> > >           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> > >           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> > >
> > > wrap2c:~# iwconfig ath0 txpower 400mW
> > > wrap2c:~# iwconfig ath0
> > > ath0      IEEE 802.11b  ESSID:"ajka-air"
> > >           Mode:Master  Frequency:2.412 GHz  Access Point: 
> 00:15:6D:10:00:43
> > >           Bit Rate:0 kb/s   Tx-Power=15 dBm   Sensitivity=0/3
> > >           Retry:off   RTS thr:off   Fragment thr:off
> > >           Encryption key:off
> > >           Power Management:off
> > >           Link Quality=0/94  Signal level=-95 dBm  Noise level=-95 dBm
> > >           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> > >           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> > >
> > > I use the following modules:
> > > ------------------------------------------------------------------
> > > ath_hal: module license 'Proprietary' taints kernel.
> > > ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
> > > wlan: 0.8.6.0 (EXPERIMENTAL)
> > > ath_rate_onoe: 1.0
> > > ath_pci: 0.9.6.0 (EXPERIMENTAL)
> > > Build date: Aug 23 2005
> > > Debugging version (IEEE80211
> > > ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> > > ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
> 24Mbps 36Mbps 48Mbps 54Mbps
> > > ath0: turboG rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
> > > ath0: H/W encryption support: WEP AES AES_CCM TKIP
> > > ath0: mac 5.9 phy 4.3 radio 4.6
> > > ath0: Use hw queue 1 for WME_AC_BE traffic
> > > ath0: Use hw queue 0 for WME_AC_BK traffic
> > > ath0: Use hw queue 2 for WME_AC_VI traffic
> > > ath0: Use hw queue 3 for WME_AC_VO traffic
> > > ath0: Use hw queue 8 for CAB traffic
> > > ath0: Use hw queue 9 for beacons
> > > Debugging version (ATH)
> > > ath0: Atheros 5212: mem=0x80040000, irq=9
> > >      ath_pci: loaded successfully
> > > 
> ================================================================================
> > >
> > > Please help ??
> > > Szabolcs Toth
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Voyage-linux mailing list
> > > Voyage-linux at list.voyage.hk
> > > http://list.voyage.hk/mailman/listinfo/voyage-linux
> >
> >
> > --
> > Regards,
> > Punky
> > P U N K N ! X . c o m
> > Technology + Lifestyle
> > (http://www.punknix.com)
> >
> > Voyage Linux
> > (http://www.voyage.hk/software/voyage.html)
> >
>
>
>_______________________________________________
>Voyage-linux mailing list
>Voyage-linux at list.voyage.hk
>http://list.voyage.hk/mailman/listinfo/voyage-linux