[Voyage-linux] Experimental booting problems on WRAP board
Punky Tse
(spam-protected)
Sat Oct 11 12:54:22 HKT 2008
daily, voyage-current is still etch. voyage-lenny is lenny.
Regards,
Punky
Frank Parker wrote:
> Apologies for the long post, but I thought the console output might
> give a good indication of the problem here. Using a WRAP board. I
> just installed the daily snapshot of 0.6 and noticed it was based on
> etch. So, I changed sources.list to point to lenny and did `apt-get
> update && apt-get dist-upgrade` . Now it hangs for several minutes
> during bootup and seems to have major problems mounting the
> filesystem.
>
> Any clues?
>
> -paker
>
> ------------------------------------------------
> Booting 'voyage-linux-10Oct08'
>
> root (hd0,0)
> Filesystem type is ext2fs, partition type 0x83
> kernel /vmlinuz root=LABEL=ROOT_FS console=ttyS0,38400n8
> [Linux-bzImage, setup=0x2800, size=0x14d9d8]
> initrd /initrd.img
> [Linux-initrd @ 0x7dd4000, 0x21b158 bytes]
>
> Linux version 2.6.23-486-voyage (2.6.23-2) (root at punknix-uml) (gcc
> version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 PR
> EEMPT Wed May 21 15:31:49 GMT 2008
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
> BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
> 0MB HIGHMEM available.
> 128MB LOWMEM available.
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 32768
> HighMem 32768 -> 32768
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 32768
> DMI not present or invalid.
> Allocating PCI resources starting at 10000000 (gap: 08000000:f7f00000)
> Built 1 zonelists in Zone order. Total pages: 32512
> Kernel command line: root=LABEL=ROOT_FS console=ttyS0,38400n8
> No local APIC present or hardware disabled
> Initializing CPU#0
> PID hash table entries: 512 (order: 9, 2048 bytes)
> Detected 233.286 MHz processor.
> Console: colour dummy device 80x25
> console [ttyS0] enabled
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Memory: 124284k/131072k available (1808k kernel code, 6244k reserved,
> 640k data, 164k init, 0k highmem)
> virtual kernel memory layout:
> fixmap : 0xfffac000 - 0xfffff000 ( 332 kB)
> pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> vmalloc : 0xc8800000 - 0xff7fe000 ( 879 MB)
> lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
> .init : 0xc0368000 - 0xc0391000 ( 164 kB)
> .data : 0xc02c4021 - 0xc036419c ( 640 kB)
> .text : 0xc0100000 - 0xc02c4021 (1808 kB)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay using timer specific routine.. 467.37 BogoMIPS (lpj=233685)
> Mount-cache hash table entries: 512
> Compat vDSO mapped to ffffe000.
> CPU: NSC Unknown stepping 01
> Checking 'hlt' instruction... OK.
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfc47b, last bus=0
> PCI: Using configuration type 1
> Setting up standard PCI resources
> SCSI subsystem initialized
> PCI: Probing PCI hardware
> PCI: Device 0000:00:12.5 not found by BIOS
> Time: tsc clocksource has been installed.
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> checking if image is initramfs... it is
> Freeing initrd memory: 2156k freed
> io scheduler noop registered
> io scheduler cfq registered (default)
> Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> SC1200: IDE controller at PCI slot 0000:00:12.2
> SC1200: chipset revision 1
> SC1200: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
> Clocksource tsc unstable (delta = -232597083 ns)
> Time: pit clocksource has been installed.
> hda: CF 1GB, CFA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: max request size: 128KiB
> hda: 2060352 sectors (1054 MB) w/0KiB Cache, CHS=2044/16/63
> hda: hda1
> i8042.c: No controller found.
> mice: PS/2 mouse device common for all mice
> padlock: VIA PadLock not detected.
> padlock: VIA PadLock Hash Engine not detected.
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Using IPI Shortcut mode
> Freeing unused kernel memory: 164k freed
> Loading, please wait...
> Begin: Loading essential drivers ... done.
> Begin: Running /scripts/init-premount ... natsemi dp8381x driver,
> version 2.1, Sept 11, 2006
> originally by Donald Becker <becker at scyld.com>
> 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
> natsemi eth0: NatSemi DP8381[56] at 0x80000000 (0000:00:0e.0),
> 00:0d:b9:06:46:f0, IRQ 10, port TP.
> natsemi eth1: NatSemi DP8381[56] at 0x80040000 (0000:00:0f.0),
> 00:0d:b9:06:46:f1, IRQ 9, port TP.
> natsemi eth2: NatSemi DP8381[56] at 0x80080000 (0000:00:10.0),
> 00:0d:b9:06:46:f2, IRQ 11, port TP.
> done.
> Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
> Begin: Running /scripts/local-premount ... done.
> Begin: Running /scripts/local-bottom ... done.
> done.
> Begin: Running /scripts/init-bottom ... done.
> INIT: version 2.86 booting
> Starting the hotplug events dispatcher: udevdudevd version 125 started
> .
> Synthesizing the initial hotplug events...done.
> Waiting for /dev to be fully populated...scx200: NatSemi SCx200 Driver
> scx200: GPIO base 0xf400
> scx200: Configuration Block base 0x9000
> done.
> Setting the system clock.
> Activating swap...done.
> EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
> /etc/rcS.d/S11hwclock.sh: line 67: /etc/adjtime: No such file or directory
> Setting the system clock.
> Cleaning up ifupdown....
> Loading kernel modules...SC1x00 Watchdog driver by Inprimis Technolgies.
> wd1100.c: a few hacks by erich.titl at think.ch
> Registered led device: wrap:error
> Registered led device: wrap:extra
> done.
> Loading device-mapper supportdevice-mapper: ioctl: 4.11.0-ioctl
> (2006-10-12) initialised: dm-devel at redhat.com
> .
> Checking file systems...fsck 1.41.0 (10-Jul-2008)
> done.
> Setting kernel variables (/etc/sysctl.conf)...done.
> Mounting local filesystems...failed.
> Activating swapfile swap...done.
> df: `/tmp': No such file or directory
> df: no file systems processed
> Setting up networking....
> Configuring network interfaces...Internet Systems Consortium DHCP Client V3.1.1
> Copyright 2004-2008 Internet Systems Consortium.
> All rights reserved.
> For info, please visit http://www.isc.org/sw/dhcp/
>
> eth0: DSPCFG accepted after 0 usec.
> eth0: link up.
> Listening on LPF/eth0/00:0d:b9:06:46:f0
> Sending on LPF/eth0/00:0d:b9:06:46:f0
> Sending on Socket/fallback
> DHCPREQUEST on eth0 to 255.255.255.255 port 67
> DHCPACK from 192.168.254.254
> bound to 192.168.254.3 -- renewal in 502641 seconds.
> if-up.d/mountnfs[eth0]: lock /var/run/network/mountnfs exist, not
> mounting failed!
> NET: Registered protocol family 10
> lo: Disabled Privacy Extensions
> done.
> Starting portmap daemon....
> /etc/rcS.d/S55bootmisc.sh: line 29: /var/run/utmp: No such file or directory
> INIT: Entering runlevel: 2
> Starting watchdog keepalive daemon: wd_keepalive.
> Starting system log daemon....
> Starting kernel log daemon... ****************** very very long pause
> here (20 -30 minutes?) ********************* failed!
> Starting DNS forwarder and DHCP server: dnsmasq
> dnsmasq: failed to open pidfile /var/run/dnsmasq.pid: No such file or directory
> failed (warning).
> failed!
> mkdir: cannot create directory `/var/run/sshd': No such file or directory
> Starting portmap daemon....
> mkdir: cannot create directory `/var/run': File exists
> chown: cannot access `/var/run/clamav': No such file or directory
> Starting ClamAV virus database updater: freshclamERROR: Can't open
> /var/log/clamav/freshclam.log in append mode (check permissi
> ons!).
> ERROR: Problem with internal logger (UpdateLogFile =
> /var/log/clamav/freshclam.log).
> failed!
> Starting advanced IEEE 802.11 management: disabled via /etc/default/hostapd.
> Not starting internet superserver: no services enabled.
> Starting PPTP Daemon: pptpd.
> DansGuardian has not been configured!
> Please edit /etc/dansguardian/dansguardian.conf manually then rerun
> this script.
> Starting periodic command scheduler: crond/usr/sbin/cron: can't open
> or create /var/run/crond.pid: No such file or directory
> failed!
> Stopping watchdog keepalive daemon:
> Starting watchdog daemon: watchdog error:
> Cannot create directory /var/log/watchdog
>
> Remounting / as read-write ... Done.
> Removing /etc/nologin ... Done.
> Remounting / as read-only ... mount: / is busy
>
> voyage login:
>
> _______________________________________________
> Voyage-linux mailing list
> Voyage-linux at list.voyage.hk
> http://list.voyage.hk/mailman/listinfo/voyage-linux
>
More information about the Voyage-linux
mailing list