Re: [Voyage-linux] Samba & Voyage 6.5

[(spam-protected)]

Why bother compiling it? Apt-get install samba is faster...
The only bad think is that samba needs RW in some folders and you should make them RW. Its /var/lib/samba, /var/cache/samba and file /etc/samba/smbpasswd. I dont know the best way to do it on voyage 0.6.5, but on Voyage 0.6 i add folders to voyage-sync  script at /etc/init.d....

> ------------ Původní zpráva ------------
> Od: Navas Abubacker <navas at truebilling.com>
> Předmět: Re: [Voyage-linux] Samba & Voyage 6.5
> Datum: 12.3.2010 09:08:16
> ----------------------------------------
> This is how I made it, for those who want an Samba on spare disk without
> doing remountrw on Flash Card
> 
> here is the compilation steps
> 
> I am assuming /mnt/ide is the path where we need to install samba
> 
> a) go to www.samba.org and grab the latest source, by the time I compiled it
> is 3.5.1
> 
> b) Extract in a temporary folder and go to the source folder and run
> ./autogen.sh from source3 directory
> 
> c) create the following directories
> 
> /mnt/ide/samba
> /mnt/ide/samba/config
> /mnt/ide/samba/state
> 
> d) run ./configure , for me it is
> 
> ./configure --prefix=/mnt/ide/samba/ --localstatedir=/mnt/ide/samba/state
> --with-configdir=/mnt/ide/samba/config
> --with-privatedir=/mnt/ide/samba/config --with-fhs --with-quotas
> --with-smbmount --with-syslog --with-utmp --with-shared-modules=idmap_rid
> --with-libsmbclient --with-automount --with-msdfs --with-ads --with-winbind
> --with-winbind-auth-challenge --with-manpages-langs=en --with-idmap
> --with-acl-support
> 
> it will take few minutes, If configure stops then install the required
> package
> 
> e) make && make install
> 
> f) put the following lines in /mnt/ide/samba/config/smb.conf
> 
> [global]
> workgroup = WORKGROUP
> netbios name = voyage
> socket options = TCP_NODELAY IPTOS_LOWDELAY SO_SNDBUF=8192
> read raw = yes
> write raw = yes
> oplocks = yes
> max xmit = 65535
> dead time = 15
> getwd cache = yes
> lpq cache = 30
> 
> [share1]
> path = /mnt/ide/data
> admin users = xxxxx
> valid users = xxxxx
> writeable = yes
> 
> g) put the following lines in /etc/init.d/samba and chmod +x and run rcconf
> for auto run
> 
> #!/bin/bash
> export PATH=$PATH:/mnt/ide/samba/bin:/mnt/ide/samba/sbin
> case "$1" in
> start)
> pkill smbd
> pkill nmbd
> /mnt/ide/samba/sbin/smbd -D
> /mnt/ide/samba/sbin/nmbd -D
> ;;
> 
> stop)
> pkill smbd
> pkill nmbd
> ;;
> reload)
> kill -SIGHUP `cat /mnt/ide/samba/state/run/smbd.pid`
> kill -SIGHUP `cat /mnt/ide/samba/state/run/nmbd.pid`
> ;;
> *)
> echo Usage:
> echo start stop reload
> ;;
> esac
> exit 0
> 
> h) add the samba lib path (at the end) in /etc/ld.so.conf
> 
> /mnt/ide/samba/lib
> 
> enjoy with your new Samba
> 
> On Fri, Mar 12, 2010 at 8:18 AM, Navas Abubacker <navas at truebilling.com>wrote:
> 
> > Oh, I didn't mean to have samba to be installed on a Flash card, perhaps on
> > the additional drive like I have a 80 GB 2.5 inch hdd connected with my
> > Alix1C
> >
> >
> > On Fri, Mar 12, 2010 at 3:52 AM, Gustin Johnson <gustin at echostar.ca>wrote:
> >
> >> -----BEGIN PGP SIGNED MESSAGE-----
> >> Hash: SHA1
> >>
> >> Navas Abubacker wrote:
> >> > I installed Voyage 6.5 on my Alix
> >> >
> >> > So far so good, Does any one knows how to install Samba with out
> >> > mounting root file system in rw ?
> >> >
> >> By definition a read only file system cannot have files written to it,
> >> so I am not aware of any way to install Samba on a read only file system.
> >> -----BEGIN PGP SIGNATURE-----
> >> Version: GnuPG v1.4.9 (GNU/Linux)
> >> Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
> >>
> >> iEYEARECAAYFAkuZbTkACgkQwRXgH3rKGfP1HgCgro3//x8WeXJMHubGm5GJXc8t
> >> Tt0An3AuGpJ3PurCtTfqot5DhHStg0Rv
> >> =OKba
> >> -----END PGP SIGNATURE-----
> >>
> >
> >
> >
> > --
> > Thanks
> > Navas
> >
> 
> 
> 
> -- 
> Thanks
> Navas
> 
> 
>