[Voyage-linux] ALIX LEDs

[John Schultz]

Still no luck. 

 

I checked /etc/depmod.d and there is no conf file for the leds. Also a grep
on dmesg for led results in the following:

[    0.226815] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11

[    0.289160] pci 0000:00:0f.4: PCI INT D disabled

[    0.289599] pci 0000:00:0f.5: PCI INT D disabled

[    1.298387] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[    1.367310] cs5535-mfd 0000:00:0f.0: MFD add devices failed: -16

[    1.367441] cs5535-mfd: probe of 0000:00:0f.0 failed with error -16

[    2.255716] i8042: probe of i8042 failed with error -5

[    2.651705] amd74xx 0000:00:0f.2: IDE port disabled

[    3.666963] hda: host side 80-wire cable detection failed, limiting max
speed to UDMA33

[    3.684604] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11

[    5.223530] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10

[    5.300132] geode-aes: GEODE AES engine enabled.

[    8.838586] Registered led device: ath9k-phy0

[    8.840782] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10

[   10.531465] Registered led device: ath9k-phy1

 

Thanks in advance,

John

 

From: Artie Gold [mailto:agold at f4winc.com] 
Sent: Friday, November 02, 2012 1:27 PM
To: John Schultz
Cc: voyage-linux at voyage.hk
Subject: Re: [Voyage-linux] ALIX LEDs

 

This may help:

 

http://pcengines.info/forums/?page=post
<http://pcengines.info/forums/?page=post&id=CB3A7583-18BF-49F5-9D39-2B171513
DEA2> &id=CB3A7583-18BF-49F5-9D39-2B171513DEA2

 

--ag

 

On Fri, Nov 2, 2012 at 2:02 PM, John Schultz <jschultz0614 at gmail.com> wrote:

Getting the same error. Well except its for that specific module J.

 

Thanks for the assist,

John

 

From: Artie Gold [mailto:agold at f4winc.com] 
Sent: Friday, November 02, 2012 12:53 PM
To: John Schultz
Cc: voyage-linux at voyage.hk
Subject: Re: [Voyage-linux] ALIX LEDs

 

Try 'modprobe leds-alix2'.

 

HTH,

--ag

On Fri, Nov 2, 2012 at 1:34 PM, John Schultz <jschultz0614 at gmail.com> wrote:

Using an alix 3d3 and version 0.8.0 dated 06/10/2012. When doing a modprobe
leds-alix, I get the following error:

 

WARNING: All config files need .conf: /etc/modprobe.d/hostap-utils, it will
be ignored in a future release.

FATAL: Module leds_alix not found.

 

What do I need to do to get this working?

 

Thanks,

John


_______________________________________________
Voyage-linux mailing list
Voyage-linux at list.voyage.hk
http://list.voyage.hk/mailman/listinfo/voyage-linux





 

-- 
Artie Gold 
Principal Software Engineer

Under Assistant West Coast Promo Man


F4W, Inc.

===================================================
Ten minutes of concentrated work can often be worth as much as several hours
of discussion, planning and coordination. And it only costs ten minutes.

 


_______________________________________________
Voyage-linux mailing list
Voyage-linux at list.voyage.hk
http://list.voyage.hk/mailman/listinfo/voyage-linux





 

-- 
Artie Gold 
Principal Software Engineer

Under Assistant West Coast Promo Man


F4W, Inc.

===================================================
Ten minutes of concentrated work can often be worth as much as several hours
of discussion, planning and coordination. And it only costs ten minutes.

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://list.voyage.hk/pipermail/voyage-linux/attachments/20121102/dd1bc44f/attachment.html>