[Voyage-linux] Errors during boot of 0.9.1 on ALIX

Punky Tse (spam-protected)
Wed Jul 17 21:08:57 HKT 2013


I can't answer all, but try my best. But almost all of them do not 
affect your operation, right?

On 7/17/2013 7:54 PM, Erik van Linstee wrote:
> I have installed 0.9.1 on an Alix board and ran into several errors 
> during boot. I reported the same errors with 0.9.0 a while back.
What ALIX board are you using?

> Here are the relevant parts of the boot log:
>
> > [    1.634822] Linux agpgart interface v0.103
> > [    1.650229] brd: module loaded
> > [    1.650525] ACPI Exception: AE_BAD_PARAMETER, Thread 3343006656 
> could not acquire Mutex [0x1] (20121018/utmutex-278)
> > [    1.654595] ACPI Exception: AE_BAD_PARAMETER, Thread 3343006656 
> could not acquire Mutex [0x1] (20121018/utmutex-278)
> > [    1.657625] cs5535-gpio cs5535-gpio: reserved resource region 
> [io  0x6100-0x61ff]
> > [    1.659422] ACPI Exception: AE_BAD_PARAMETER, Thread 3343006656 
> could not acquire Mutex [0x1] (20121018/utmutex-278)
> > [    1.663458] ACPI Exception: AE_BAD_PARAMETER, Thread 3343006656 
> could not acquire Mutex [0x1] (20121018/utmutex-278)
> > [    1.668559] ACPI Exception: AE_BAD_PARAMETER, Thread 3343006656 
> could not acquire Mutex [0x1] (20121018/utmutex-278)
> > [    1.672595] cs5535-mfd 0000:00:0f.0: 5 devices registered.
Not sure, perhaps you are using ALIX3d3.

> > Begin: Running /scripts/init-bottom ... Setting up serial console 
> for inittab ...
> > DEFCONSOLE=console=ttyS0,38400n8
> > LIVE_GETTY=
> > AUTOINSTALL=
> > Setting Serial Port to ttyS0 38400
> > sed: can't create temp file '/root/etc/inittabYp7rxF': Read-only 
> file system
> > done.
This is used for PXE installation, could safely ignore.

> > [    6.488793] Error: Driver 'pcspkr' is already registered, 
> aborting...

> > [info] Loading kernel module w83627hf.
> > ERROR: could not insert 'w83627hf': No such device
w83627 no longer be used for ALIX, not sure why.  But should be remove 
from ALIX installation profile.
> > can't create /var/lib/dhcp/dhclient.eth0.leases: No such file or 
> directory
> Actually, the directory does exist, by /var/lib/dhcp is mounted readonly.
Known, the leases file remember what IP your have leased.  If this bugs 
you,  you can add "var/lib/dhcp" to $VOYAGE_SYNC_RECOVER_DIRS and/or 
$VOYAGE_SYNC_DIRS in /etc/default/voyage-sync

> > [....] Starting OpenBSD Secure Shell server: sshdCould not load host 
> key: /etc/ssh/ssh_host_ecdsa_key
> > . ok
> This error can be fixed by removing the following line from 
> /etc/ssh/sshd_config:
> > HostKey /etc/ssh/ssh_host_ecdsa_key 
> Or by creating the key manually.
This was fixed in voyage-util 0.12-4, after 0.9.1, the key could be 
regenerated by "dpkg-reconfigure openssh-server"

> Also, the leds module does not seem to be available anymore (since 
> 0.8.x).
> > root at voyage:~# modprobe leds-alix
> > FATAL: Module leds-alix not found.
leds-alix is obsoleted.  Leds is now using GPIO_CS5535 to drive. Works 
on ALIX2 and ALIX3d2.

> regards,
> Erik

-- 

Regards,
Kim-man "Punky" Tse

* Open Source Embedded Solutions and Systems
   - Voyage Linux (http://linux.voyage.hk)
   - Voyage MPD   (http://linux.voyage.hk/voyage-mpd)
   - Voyage MuBox (http://mubox.voyage.hk)
* Voyage Store   (http://store.voyage.hk)




More information about the Voyage-linux mailing list