ifpu eth0 says:  Ignoring unknown interface eth0=eth0.<br>
<br>Max.<br><br><div class="gmail_quote">On Wed, Jun 24, 2009 at 3:04 AM, Kim-man 'Punky' TSE <span dir="ltr"><<a href="mailto:punkytse@punknix.com">punkytse@punknix.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Hi Max,<br>
<br>
My analysis is still not conclusive.<br>
Before you switch to 0.5.2, try "ifup eth0" to see if you can bring up eth0 and function properly. <br><div class="im">
Regards,<br>
Punky<br>
<br>
<br>
<br>
Max Bridgewater wrote:<br>
</div><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Hi Punky,<br>
<br><div class="im">
After seing the result of ifconfig, i also had some suspicion about DHCP. But then,  earlier today (about 4h ago) I booted the very same box with Voyage 0.5.2, in the very same position, with the very same ethernet cable, connected to the very same router. And i tried booting the 0.6.1 version at least twice. I thus, doubt that it is a DHCP problem. But if you want me to, i can try to boot again with 0.5.2.<br>

<br>
Maybe it would be easier to start from Voyage 0.5.2? I couldn't figure out how to customize it though.<br>
<br>
Cheers,<br>
Max.<br>
<br></div><div class="im">
On Wed, Jun 24, 2009 at 2:38 AM, Kim-man 'Punky' TSE <<a href="mailto:punkytse@punknix.com" target="_blank">punkytse@punknix.com</a> <mailto:<a href="mailto:punkytse@punknix.com" target="_blank">punkytse@punknix.com</a>>> wrote:<br>

<br>
    Hi Max,<br>
<br>
    >From ifconfig, eth0 should be the network interface.  It is just<br>
    that eth0 is not started or failed in getting DHCP lease?<br>
<br>
    Something a bit strange is that eth0 should use IRQ15 but I can't<br>
    find it in /proc/interrupts.<br>
<br>
<br>
    Regards,<br>
    Punky<br>
<br>
    Max Bridgewater wrote:<br>
<br>
        Hi Punky,<br>
<br>
        Attached are three documents with the result of each of these<br>
        commands.<br>
<br>
        Ad Sean: curious to know which version of Voyage are you<br>
        running? I've never tried the CF because my notebook doesn't<br>
        support one.<br>
<br>
        Thanks again,<br>
        Max.<br>
<br>
        On Wed, Jun 24, 2009 at 2:10 AM, Kim-man 'Punky' TSE<br>
        <<a href="mailto:punkytse@punknix.com" target="_blank">punkytse@punknix.com</a> <mailto:<a href="mailto:punkytse@punknix.com" target="_blank">punkytse@punknix.com</a>><br></div>
        <mailto:<a href="mailto:punkytse@punknix.com" target="_blank">punkytse@punknix.com</a> <mailto:<a href="mailto:punkytse@punknix.com" target="_blank">punkytse@punknix.com</a>>>><div class="im"><br>
        wrote:<br>
<br>
           Hi Max,<br>
<br>
           I see r6040 driver is loaded via udev.  Please show me the<br>
        output<br>
           of the following:<br>
           1. lspci -v<br>
           2. ifconfig -a<br>
           3. cat /proc/interrupts<br>
<br>
           - Punky<br>
<br>
<br>
<br>
    --     Regards,<br>
    Punky<br>
<br>
    Voyage Solutions (<a href="http://solution.voyage.hk" target="_blank">http://solution.voyage.hk</a>)<br>
    * Embedded Solutions and Systems<br>
     - Mesh Networking, Captive Portal, IP Surveillance, VoIP/PBX<br>
     - Network Engineering, Development Platform and Consultation<br>
             <br>
<br>
</div></blockquote><div><div></div><div class="h5">
<br>
<br>
-- <br>
Regards,<br>
Punky<br>
<br>
Voyage Solutions (<a href="http://solution.voyage.hk" target="_blank">http://solution.voyage.hk</a>)<br>
* Embedded Solutions and Systems<br>
 - Mesh Networking, Captive Portal, IP Surveillance, VoIP/PBX<br>
 - Network Engineering, Development Platform and Consultation<br>
         <br>
<br>
</div></div></blockquote></div><br>