[Voyage-products] problems with WRAP board hangin on voyage

[George J. Borsuk]

I have a wrap board and have been going nuts with it.

 

It boots and then I get the following and it locks.  Any ideas.  I'm at my wits end.

The board works as I put monowall on it and it booted fine..

 

PC Engines WRAP.1C/1D/1E v1.10                              

640 KB Base Memory                  

130048 KB Extended Memory                         

 

01F0 Master 848A SanDisk SDCFB-1024                                   

Phys C/H/S 1986/16/63 Log C/H/S 993/32/63                                         

 

LI  

LILLOO  2222..66..11  LLooaaddiinngg  LLiinnuuxx................................                                                                                

....    

 

BBIIOOSS  ddaattaa  cchheecckk  ssuucccceessssffuull                                                    

 

Linux version 2.6.8-486-voyage (root at punknix-uml) (gcc version 3.3.5 (Debian 1:3                                                                                

.3.5-8)) #1 Mon Feb 14 18:38:42 GMT 2005                                        

BIOS-provided physical RAM map:                               

 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)                                                        

 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)                                                          

 BIOS-e820: 0000000000100000 - 0000000008000000 (usable)                                                        

 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)                                                          

128MB LOWMEM available.                       

DMI not present.                

ACPI: Unable to locate RSDP                           

Built 1 zonelists                 

Kernel command line: auto BOOT_IMAGE=Linux ro root=301 console=ttyS0,9600n8                                                                           

No local APIC present or hardware disabled                                      

Initializing CPU#0

PID hash table entries: 1024 (order 10: 8192 bytes)

Detected 266.663 MHz processor.

Using tsc for high-res timesource

Console: colour dummy device 80x25

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 126984k/131072k available (1182k kernel code, 3520k reserved, 680k data,

 100k init, 0k highmem)

Checking if this processor honours the WP bit even in supervisor mode... Ok.

Calibrating delay loop... 524.28 BogoMIPS

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

CPU: NSC Unknown stepping 01

Checking 'hlt' instruction... OK.

NET: Registered protocol family 16

PCI: PCI BIOS revision 2.10 entry at 0xfc46b, last bus=0

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Probing PCI hardware (bus 00)

................................

PCI: Device 00:95 not found by BIOS

Initializing Cryptographic API

Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled

`ÍÉ%¤[` <

 

 

I get garbled text and then nothing...

 

Any ideas?

 

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://list.voyage.hk/pipermail/voyage-products/attachments/20051217/2cdd139b/attachment.htm