[Voyage-linux] Problem with Microclient JrDx diskless install
Jon Trauntvein
(spam-protected)
Mon Mar 9 20:28:33 HKT 2009
Kim-man 'Punky' TSE wrote:
> Jon,
>
> You don't officially supprt MicroClient JrDx, although Voyage Linux
> should run on any embedded x86 platforms.
>
> Please post your serial console output for further investigation.
> Thanks.
>
> Regards,
> Punky
>
> Jon Trauntvein wrote:
>> I am trying to install voyage on a a microSD card for a MicroClient
>> JrDx. Following the installation instructions, I am having a problem
>> with formatting the microSD card. It will appear to start working
>> but, in the end, I will get console messages that IRQ14 has been
>> disabled and the device then appears to hang. Has anyone else
>> encountered this kind of issue?
Here is the content of the message log (dmesg) after the IRQ14 event
occurs. I don't have a CF card at this location but will try it when I
get to my work location later this morning.
ghMem 65536 -> 65536
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65536
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 480 pages used for memmap
[ 0.000000] Normal zone: 60960 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI not present or invalid.
[ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found
[20080321]
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
10000000:ef000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 -
0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 65024
[ 0.000000] Kernel command line: initrd=/live/initrd1.img boot=live
noautologin noxautologin nouser debug all_generic_ide nolocales
username=root hostname=voyage union=aufs BOOT_IMAGE=/live/vmlinuz1
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] mapped APIC to ffffb000 (01202000)
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 1000.036 MHz processor.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000999] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000999] Memory: 251712k/262144k available (1973k kernel code,
9932k reserved, 751k data, 288k init, 0k highmem)
[ 0.000999] virtual kernel memory layout:
[ 0.000999] fixmap : 0xfffa7000 - 0xfffff000 ( 352 kB)
[ 0.000999] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000999] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 0.000999] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000999] .init : 0xc03ac000 - 0xc03f4000 ( 288 kB)
[ 0.000999] .data : 0xc02ed4af - 0xc03a9498 ( 751 kB)
[ 0.000999] .text : 0xc0100000 - 0xc02ed4af (1973 kB)
[ 0.000999] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.061639] Calibrating delay using timer specific routine.. 2002.20
BogoMIPS (lpj=1001100)
[ 0.061990] Mount-cache hash table entries: 512
[ 0.062843] CPU: Vortex86 SoC 05/02 stepping 02
[ 0.062990] Checking 'hlt' instruction... OK.
[ 0.066667] Freeing SMP alternatives: 0k freed
[ 0.066737] ACPI: Core revision 20080321
[ 0.066981] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While
loading namespace from ACPI tables [20080321]
[ 0.066989] ACPI: Unable to load the System Description Tables
[ 0.068078] net_namespace: 628 bytes
[ 0.068962] NET: Registered protocol family 16
[ 0.070855] EISA bus registered
[ 0.080818] PCI: Using configuration type 1 for base access
[ 0.080910] Setting up standard PCI resources
[ 0.093621] ACPI: Interpreter disabled.
[ 0.093712] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.094148] pnp: PnP ACPI: disabled
[ 0.095778] SCSI subsystem initialized
[ 0.097216] PCI: Probing PCI hardware
[ 0.097297] PCI: Probing PCI hardware (bus 00)
[ 0.102084] PCI: Using IRQ router default [17f3/6031] at 0000:00:07.0
[ 0.106867] NET: Registered protocol family 2
[ 0.107467] IP route cache hash table entries: 2048 (order: 1, 8192
bytes)
[ 0.108697] TCP established hash table entries: 8192 (order: 4, 65536
bytes)
[ 0.109083] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.109293] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.109373] TCP reno registered
[ 0.109810] NET: Registered protocol family 1
[ 0.110541] checking if image is initramfs... it is
[ 2.120026] Freeing initrd memory: 4152k freed
[ 2.121477] platform rtc_cmos: registered platform RTC device (no PNP
device found)
[ 2.123293] microcode: CPU0 not a capable Intel processor
[ 2.123385] IA-32 Microcode Update Driver: v1.14a
<tigran at aivazian.fsnet.co.uk>
[ 2.127574] msgmni has been set to 499
[ 2.127972] io scheduler noop registered
[ 2.128045] io scheduler anticipatory registered
[ 2.128116] io scheduler deadline registered
[ 2.128248] io scheduler cfq registered (default)
[ 2.128348] pci 0000:00:03.0: Boot video device
[ 2.368098] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 2.612625] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.856582] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.870087] brd: module loaded
[ 2.870508] Driver 'sd' needs updating - please use bus_type methods
[ 2.871856] PNP: No PS/2 controller found. Probing ports directly.
[ 2.874412] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.874540] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.875794] mice: PS/2 mouse device common for all mice
[ 2.899999] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.948801] EISA: Probing bus 0 at eisa.0
[ 2.951322] TCP cubic registered
[ 2.951404] NET: Registered protocol family 17
[ 2.951993] RPC: Registered udp transport module.
[ 2.952078] RPC: Registered tcp transport module.
[ 2.952209] Using IPI Shortcut mode
[ 2.955165] Freeing unused kernel memory: 288k freed
[ 3.337820] Uniform Multi-Platform E-IDE driver
[ 3.337925] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 3.343035] ide_generic: please use "probe_mask=0x3f" module
parameter for probing all legacy ISA IDE ports
[ 3.343205] Probing IDE interface ide0...
[ 3.606417] hda: SU02G RDC SD-IDE HOST CONTROLLER, ATA DISK drive
[ 4.218570] Probing IDE interface ide1...
[ 4.731503] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.731717] ide1 at 0x170-0x177,0x376 on irq 15
[ 9.485064] hda: max request size: 128KiB
[ 9.485160] hda: 3970048 sectors (2032 MB) w/0KiB Cache, CHS=3938/16/63
[ 9.485437] hda: cache flushes supported
[ 9.485696] hda: hda1
[ 10.063202] usbcore: registered new interface driver usbfs
[ 10.063485] usbcore: registered new interface driver hub
[ 10.067549] usbcore: registered new device driver usb
[ 10.093042] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[ 10.093313] ohci_hcd 0000:00:0a.0: OHCI Host Controller
[ 10.093863] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned
bus number 1
[ 10.094039] ohci_hcd 0000:00:0a.0: irq 6, io mem 0x000e2000
[ 10.176647] usb usb1: configuration #1 chosen from 1 choice
[ 10.176953] hub 1-0:1.0: USB hub found
[ 10.177116] hub 1-0:1.0: 2 ports detected
[ 10.281943] ehci_hcd 0000:00:0a.1: EHCI Host Controller
[ 10.282255] ehci_hcd 0000:00:0a.1: new USB bus registered, assigned
bus number 2
[ 10.303202] ehci_hcd 0000:00:0a.1: irq 7, io mem 0x000e3000
[ 10.311594] ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 10.312192] usb usb2: configuration #1 chosen from 1 choice
[ 10.312519] hub 2-0:1.0: USB hub found
[ 10.312644] hub 2-0:1.0: 2 ports detected
[ 10.414039] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 10.414346] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned
bus number 3
[ 10.414516] ohci_hcd 0000:00:0b.0: irq 5, io mem 0x000e0000
[ 10.495950] usb usb3: configuration #1 chosen from 1 choice
[ 10.496303] hub 3-0:1.0: USB hub found
[ 10.496432] hub 3-0:1.0: 2 ports detected
[ 10.658999] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 10.658999] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned
bus number 4
[ 10.680574] ehci_hcd 0000:00:0b.1: irq 9, io mem 0x000e1000
[ 10.686681] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 10.688560] usb usb4: configuration #1 chosen from 1 choice
[ 10.689996] hub 4-0:1.0: USB hub found
[ 10.690184] hub 4-0:1.0: 2 ports detected
[ 11.102996] usb 4-1: new high speed USB device using ehci_hcd and
address 2
[ 11.218287] usb 4-1: configuration #1 chosen from 1 choice
[ 11.323761] Initializing USB Mass Storage driver...
[ 11.435883] usb 1-2: new full speed USB device using ohci_hcd and
address 2
[ 11.571517] usb 1-2: configuration #1 chosen from 1 choice
[ 11.579329] scsi0 : SCSI emulation for USB Mass Storage devices
[ 11.588224] usbcore: registered new interface driver usb-storage
[ 11.588338] USB Mass Storage support registered.
[ 11.589669] usb-storage: device found at 2
[ 11.589757] usb-storage: waiting for device to settle before scanning
[ 11.923611] usbcore: registered new interface driver hiddev
[ 11.923916] usbcore: registered new interface driver usbhid
[ 11.924008] usbhid: v2.6:USB HID core driver
[ 16.595876] scsi 0:0:0:0: CD-ROM PLEXTOR DVDR PX-716A
1.11 PQ: 0 ANSI: 0 CCS
[ 16.597883] usb-storage: device scan complete
[ 16.753845] Driver 'sr' needs updating - please use bus_type methods
[ 16.818469] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 16.818589] Uniform CD-ROM driver Revision: 3.20
[ 16.819228] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 16.935327] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 30.623122] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 30.651990] ISO 9660 Extensions: RRIP_1991A
[ 30.753289] aufs 20080714
[ 30.908844] loop: module loaded
[ 31.117562] squashfs: version 3.3-CVS (2008/04/04) Phillip Lougher
[ 58.915974] udevd version 125 started
[ 68.898247] <6>r6040: RDC R6040 NAPI net driver,version 0.16 (10Nov2007)
[ 68.898269]
[ 69.276550] input: PC Speaker as /class/input/input1
[ 69.969743] usbcore: registered new interface driver snd-usb-audio
[ 73.267775] natsemi dp8381x driver, version 2.1, Sept 11, 2006
[ 73.267797] originally by Donald Becker <becker at scyld.com>
[ 73.267809] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
[ 73.426788] ieee80211_crypt: registered algorithm 'NULL'
[ 75.144130] aufs test_add:336:mount[4094]: nested aufs /var/log
[ 75.213715] aufs test_add:336:mount[4100]: nested aufs /var/tmp
[ 77.723062] Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
[ 81.570266] NET: Registered protocol family 10
[ 81.573002] lo: Disabled Privacy Extensions
[ 801.359049] usb 4-2: new high speed USB device using ehci_hcd and
address 3
[ 801.478598] usb 4-2: configuration #1 chosen from 1 choice
[ 801.492847] scsi1 : SCSI emulation for USB Mass Storage devices
[ 801.499028] usb-storage: device found at 3
[ 801.499132] usb-storage: waiting for device to settle before scanning
[ 806.499900] scsi 1:0:0:0: Direct-Access Flash Drive SM_USB20
1100 PQ: 0 ANSI: 0 CCS
[ 806.504712] sd 1:0:0:0: [sda] 501760 512-byte hardware sectors (257 MB)
[ 806.506165] sd 1:0:0:0: [sda] Write Protect is off
[ 806.506277] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 806.506369] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 806.510859] sd 1:0:0:0: [sda] 501760 512-byte hardware sectors (257 MB)
[ 806.512603] sd 1:0:0:0: [sda] Write Protect is off
[ 806.512725] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 806.512814] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 806.512926] sda: sda1
[ 806.529667] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 806.530084] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 806.531587] usb-storage: device scan complete
[ 817.694171] usb 4-2: USB disconnect, address 3
[ 899.694520] usb 4-2: new high speed USB device using ehci_hcd and
address 4
[ 899.814061] usb 4-2: configuration #1 chosen from 1 choice
[ 899.830567] scsi2 : SCSI emulation for USB Mass Storage devices
[ 899.845630] usb-storage: device found at 4
[ 899.846365] usb-storage: waiting for device to settle before scanning
[ 904.847353] scsi 2:0:0:0: Direct-Access Flash Drive SM_USB20
1100 PQ: 0 ANSI: 0 CCS
[ 904.851035] sd 2:0:0:0: [sda] 501760 512-byte hardware sectors (257 MB)
[ 904.852432] sd 2:0:0:0: [sda] Write Protect is off
[ 904.852600] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 904.852691] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 904.857481] sd 2:0:0:0: [sda] 501760 512-byte hardware sectors (257 MB)
[ 904.859375] sd 2:0:0:0: [sda] Write Protect is off
[ 904.859513] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 904.859638] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 904.859756] sda: sda1
[ 904.878172] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 904.878588] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 904.880110] usb-storage: device scan complete
[ 977.851568] FAT: invalid media value (0xb9)
[ 977.851676] VFS: Can't find a valid FAT filesystem on dev sda.
[ 1072.369305] hda: hda1
[ 1074.383206] hda: hda1
[ 1166.233993] irq 14: nobody cared (try booting with the "irqpoll" option)
[ 1166.234132] Pid: 4658, comm: mkfs.ext2 Not tainted 2.6.26-486-voyage #1
[ 1166.234220] [<c01355ef>] __report_bad_irq+0x24/0x69
[ 1166.234264] [<c01355f6>] __report_bad_irq+0x2b/0x69
[ 1166.234264] [<c0135817>] note_interrupt+0x1e3/0x238
[ 1166.234264] [<c0134f8f>] handle_IRQ_event+0x1a/0x3f
[ 1166.234264] [<c0135e85>] handle_level_irq+0x8a/0xce
[ 1166.234264] [<c0105252>] do_IRQ+0x4b/0x61
[ 1166.234264] [<c0103b63>] common_interrupt+0x23/0x30
[ 1166.234264] [<c0117f42>] __do_softirq+0x2c/0x78
[ 1166.234264] [<c0117fb0>] do_softirq+0x22/0x26
[ 1166.234264] [<c01180c9>] irq_exit+0x25/0x5d
[ 1166.234264] [<c0105257>] do_IRQ+0x50/0x61
[ 1166.234264] [<c0103b63>] common_interrupt+0x23/0x30
[ 1166.234264] [<c01dceed>] __make_request+0x2a6/0x2d1
[ 1166.234264] [<c01d0060>] crypto_attr_alg+0x0/0x46
[ 1166.234264] [<c0120000>] call_usermodehelper_exec+0x10/0x98
[ 1166.234264] [<c010fe2f>] task_tick_fair+0x3a/0x58
[ 1166.234264] [<c01dbfa6>] generic_make_request+0x28c/0x2b9
[ 1166.234264] [<c010fe2f>] task_tick_fair+0x3a/0x58
[ 1166.234264] [<c0112224>] scheduler_tick+0x85/0xa5
[ 1166.234264] [<c0139957>] mempool_alloc+0x27/0xe5
[ 1166.234264] [<c01dc092>] submit_bio+0xbf/0xc7
[ 1166.234264] [<c0171dfe>] bio_alloc_bioset+0x9a/0xfe
[ 1166.234264] [<c016eb66>] submit_bh+0xbe/0xda
[ 1166.234264] [<c0170f87>] __block_write_full_page+0x1eb/0x2b6
[ 1166.234264] [<c0172c7e>] blkdev_get_block+0x0/0x42
[ 1166.234264] [<c0171118>] block_write_full_page+0xc6/0xcf
[ 1166.234264] [<c0172c7e>] blkdev_get_block+0x0/0x42
[ 1166.234264] [<c013c52f>] __writepage+0x8/0x22
[ 1166.234264] [<c013cc93>] write_cache_pages+0x152/0x25d
[ 1166.234265] [<c013c527>] __writepage+0x0/0x22
[ 1166.234265] [<c013cd9e>] generic_writepages+0x0/0x21
[ 1166.234265] [<c013cdb8>] generic_writepages+0x1a/0x21
[ 1166.234265] [<c013cddf>] do_writepages+0x20/0x30
[ 1166.234265] [<c013812a>] __filemap_fdatawrite_range+0x64/0x6f
[ 1166.234265] [<c0138318>] filemap_fdatawrite+0x12/0x16
[ 1166.234265] [<c016df9c>] do_fsync+0x23/0x6b
[ 1166.234265] [<c016e000>] __do_fsync+0x1c/0x2b
[ 1166.234265] [<c0102c32>] syscall_call+0x7/0xb
[ 1166.234265] [<c02e0000>] svc_recv+0x19c/0x6df
[ 1166.234265] =======================
[ 1166.234265] handlers:
[ 1166.234265] [<d08260ff>] (ide_intr+0x0/0x1df [ide_core])
[ 1166.234265] Disabling IRQ #14
[ 1196.195637] hda: lost interrupt
Thanks,
Jon Trauntvein
More information about the Voyage-linux
mailing list