[Voyage-linux] Problem with Microclient JrDx diskless install
Punky Tse
(spam-protected)
Mon Mar 9 23:50:46 HKT 2009
Hi Jon,
From dmesg output, I see the followings:
1. You are booting from live-cd. Is it a IDE or usb device?
2. What was that ide device for hda?
3. Your device has two USB-based flash drive (sda1). I think one slot
is CF and the other is SD?
Can you try to unplug hda and flash devices and just boot from cd?
Regards,
Punky
Jon Trauntvein wrote:
> Kim-man 'Punky' TSE wrote:
>> Jon,
>>
>> You don't officially supprt MicroClient JrDx, although Voyage Linux
>> should run on any embedded x86 platforms.
>>
>> Please post your serial console output for further investigation.
>> Thanks.
>>
>> Regards,
>> Punky
>>
>> Jon Trauntvein wrote:
>>> I am trying to install voyage on a a microSD card for a MicroClient
>>> JrDx. Following the installation instructions, I am having a
>>> problem with formatting the microSD card. It will appear to start
>>> working but, in the end, I will get console messages that IRQ14 has
>>> been disabled and the device then appears to hang. Has anyone else
>>> encountered this kind of issue?
> Here is the content of the message log (dmesg) after the IRQ14 event
> occurs. I don't have a CF card at this location but will try it when
> I get to my work location later this morning.
>
>
> ghMem 65536 -> 65536
> [ 0.000000] Movable zone start PFN for each node
> [ 0.000000] early_node_map[1] active PFN ranges
> [ 0.000000] 0: 0 -> 65536
> [ 0.000000] On node 0 totalpages: 65536
> [ 0.000000] DMA zone: 32 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 4064 pages, LIFO batch:0
> [ 0.000000] Normal zone: 480 pages used for memmap
> [ 0.000000] Normal zone: 60960 pages, LIFO batch:15
> [ 0.000000] HighMem zone: 0 pages used for memmap
> [ 0.000000] Movable zone: 0 pages used for memmap
> [ 0.000000] DMI not present or invalid.
> [ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found
> [20080321]
> [ 0.000000] Allocating PCI resources starting at 20000000 (gap:
> 10000000:ef000000)
> [ 0.000000] PM: Registered nosave memory: 000000000009f000 -
> 00000000000a0000
> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
> 00000000000e0000
> [ 0.000000] PM: Registered nosave memory: 00000000000e0000 -
> 0000000000100000
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 65024
> [ 0.000000] Kernel command line: initrd=/live/initrd1.img boot=live
> noautologin noxautologin nouser debug all_generic_ide nolocales
> username=root hostname=voyage union=aufs BOOT_IMAGE=/live/vmlinuz1
> [ 0.000000] No local APIC present or hardware disabled
> [ 0.000000] mapped APIC to ffffb000 (01202000)
> [ 0.000000] Initializing CPU#0
> [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
> [ 0.000000] Detected 1000.036 MHz processor.
> [ 0.000999] Console: colour VGA+ 80x25
> [ 0.000999] console [tty0] enabled
> [ 0.000999] Dentry cache hash table entries: 32768 (order: 5,
> 131072 bytes)
> [ 0.000999] Inode-cache hash table entries: 16384 (order: 4, 65536
> bytes)
> [ 0.000999] Memory: 251712k/262144k available (1973k kernel code,
> 9932k reserved, 751k data, 288k init, 0k highmem)
> [ 0.000999] virtual kernel memory layout:
> [ 0.000999] fixmap : 0xfffa7000 - 0xfffff000 ( 352 kB)
> [ 0.000999] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> [ 0.000999] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
> [ 0.000999] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
> [ 0.000999] .init : 0xc03ac000 - 0xc03f4000 ( 288 kB)
> [ 0.000999] .data : 0xc02ed4af - 0xc03a9498 ( 751 kB)
> [ 0.000999] .text : 0xc0100000 - 0xc02ed4af (1973 kB)
> [ 0.000999] Checking if this processor honours the WP bit even in
> supervisor mode...Ok.
> [ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
> [ 0.061639] Calibrating delay using timer specific routine..
> 2002.20 BogoMIPS (lpj=1001100)
> [ 0.061990] Mount-cache hash table entries: 512
> [ 0.062843] CPU: Vortex86 SoC 05/02 stepping 02
> [ 0.062990] Checking 'hlt' instruction... OK.
> [ 0.066667] Freeing SMP alternatives: 0k freed
> [ 0.066737] ACPI: Core revision 20080321
> [ 0.066981] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While
> loading namespace from ACPI tables [20080321]
> [ 0.066989] ACPI: Unable to load the System Description Tables
> [ 0.068078] net_namespace: 628 bytes
> [ 0.068962] NET: Registered protocol family 16
> [ 0.070855] EISA bus registered
> [ 0.080818] PCI: Using configuration type 1 for base access
> [ 0.080910] Setting up standard PCI resources
> [ 0.093621] ACPI: Interpreter disabled.
> [ 0.093712] Linux Plug and Play Support v0.97 (c) Adam Belay
> [ 0.094148] pnp: PnP ACPI: disabled
> [ 0.095778] SCSI subsystem initialized
> [ 0.097216] PCI: Probing PCI hardware
> [ 0.097297] PCI: Probing PCI hardware (bus 00)
> [ 0.102084] PCI: Using IRQ router default [17f3/6031] at 0000:00:07.0
> [ 0.106867] NET: Registered protocol family 2
> [ 0.107467] IP route cache hash table entries: 2048 (order: 1, 8192
> bytes)
> [ 0.108697] TCP established hash table entries: 8192 (order: 4,
> 65536 bytes)
> [ 0.109083] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> [ 0.109293] TCP: Hash tables configured (established 8192 bind 8192)
> [ 0.109373] TCP reno registered
> [ 0.109810] NET: Registered protocol family 1
> [ 0.110541] checking if image is initramfs... it is
> [ 2.120026] Freeing initrd memory: 4152k freed
> [ 2.121477] platform rtc_cmos: registered platform RTC device (no
> PNP device found)
> [ 2.123293] microcode: CPU0 not a capable Intel processor
> [ 2.123385] IA-32 Microcode Update Driver: v1.14a
> <tigran at aivazian.fsnet.co.uk>
> [ 2.127574] msgmni has been set to 499
> [ 2.127972] io scheduler noop registered
> [ 2.128045] io scheduler anticipatory registered
> [ 2.128116] io scheduler deadline registered
> [ 2.128248] io scheduler cfq registered (default)
> [ 2.128348] pci 0000:00:03.0: Boot video device
> [ 2.368098] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
> IRQ sharing enabled
> [ 2.612625] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 2.856582] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> [ 2.870087] brd: module loaded
> [ 2.870508] Driver 'sd' needs updating - please use bus_type methods
> [ 2.871856] PNP: No PS/2 controller found. Probing ports directly.
> [ 2.874412] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 2.874540] serio: i8042 AUX port at 0x60,0x64 irq 12
> [ 2.875794] mice: PS/2 mouse device common for all mice
> [ 2.899999] input: AT Translated Set 2 keyboard as /class/input/input0
> [ 2.948801] EISA: Probing bus 0 at eisa.0
> [ 2.951322] TCP cubic registered
> [ 2.951404] NET: Registered protocol family 17
> [ 2.951993] RPC: Registered udp transport module.
> [ 2.952078] RPC: Registered tcp transport module.
> [ 2.952209] Using IPI Shortcut mode
> [ 2.955165] Freeing unused kernel memory: 288k freed
> [ 3.337820] Uniform Multi-Platform E-IDE driver
> [ 3.337925] ide: Assuming 33MHz system bus speed for PIO modes;
> override with idebus=xx
> [ 3.343035] ide_generic: please use "probe_mask=0x3f" module
> parameter for probing all legacy ISA IDE ports
> [ 3.343205] Probing IDE interface ide0...
> [ 3.606417] hda: SU02G RDC SD-IDE HOST CONTROLLER, ATA DISK drive
> [ 4.218570] Probing IDE interface ide1...
> [ 4.731503] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> [ 4.731717] ide1 at 0x170-0x177,0x376 on irq 15
> [ 9.485064] hda: max request size: 128KiB
> [ 9.485160] hda: 3970048 sectors (2032 MB) w/0KiB Cache,
> CHS=3938/16/63
> [ 9.485437] hda: cache flushes supported
> [ 9.485696] hda: hda1
> [ 10.063202] usbcore: registered new interface driver usbfs
> [ 10.063485] usbcore: registered new interface driver hub
> [ 10.067549] usbcore: registered new device driver usb
> [ 10.093042] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
> (OHCI) Driver
> [ 10.093313] ohci_hcd 0000:00:0a.0: OHCI Host Controller
> [ 10.093863] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned
> bus number 1
> [ 10.094039] ohci_hcd 0000:00:0a.0: irq 6, io mem 0x000e2000
> [ 10.176647] usb usb1: configuration #1 chosen from 1 choice
> [ 10.176953] hub 1-0:1.0: USB hub found
> [ 10.177116] hub 1-0:1.0: 2 ports detected
> [ 10.281943] ehci_hcd 0000:00:0a.1: EHCI Host Controller
> [ 10.282255] ehci_hcd 0000:00:0a.1: new USB bus registered, assigned
> bus number 2
> [ 10.303202] ehci_hcd 0000:00:0a.1: irq 7, io mem 0x000e3000
> [ 10.311594] ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00,
> driver 10 Dec 2004
> [ 10.312192] usb usb2: configuration #1 chosen from 1 choice
> [ 10.312519] hub 2-0:1.0: USB hub found
> [ 10.312644] hub 2-0:1.0: 2 ports detected
> [ 10.414039] ohci_hcd 0000:00:0b.0: OHCI Host Controller
> [ 10.414346] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned
> bus number 3
> [ 10.414516] ohci_hcd 0000:00:0b.0: irq 5, io mem 0x000e0000
> [ 10.495950] usb usb3: configuration #1 chosen from 1 choice
> [ 10.496303] hub 3-0:1.0: USB hub found
> [ 10.496432] hub 3-0:1.0: 2 ports detected
> [ 10.658999] ehci_hcd 0000:00:0b.1: EHCI Host Controller
> [ 10.658999] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned
> bus number 4
> [ 10.680574] ehci_hcd 0000:00:0b.1: irq 9, io mem 0x000e1000
> [ 10.686681] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00,
> driver 10 Dec 2004
> [ 10.688560] usb usb4: configuration #1 chosen from 1 choice
> [ 10.689996] hub 4-0:1.0: USB hub found
> [ 10.690184] hub 4-0:1.0: 2 ports detected
> [ 11.102996] usb 4-1: new high speed USB device using ehci_hcd and
> address 2
> [ 11.218287] usb 4-1: configuration #1 chosen from 1 choice
> [ 11.323761] Initializing USB Mass Storage driver...
> [ 11.435883] usb 1-2: new full speed USB device using ohci_hcd and
> address 2
> [ 11.571517] usb 1-2: configuration #1 chosen from 1 choice
> [ 11.579329] scsi0 : SCSI emulation for USB Mass Storage devices
> [ 11.588224] usbcore: registered new interface driver usb-storage
> [ 11.588338] USB Mass Storage support registered.
> [ 11.589669] usb-storage: device found at 2
> [ 11.589757] usb-storage: waiting for device to settle before scanning
> [ 11.923611] usbcore: registered new interface driver hiddev
> [ 11.923916] usbcore: registered new interface driver usbhid
> [ 11.924008] usbhid: v2.6:USB HID core driver
> [ 16.595876] scsi 0:0:0:0: CD-ROM PLEXTOR DVDR
> PX-716A 1.11 PQ: 0 ANSI: 0 CCS
> [ 16.597883] usb-storage: device scan complete
> [ 16.753845] Driver 'sr' needs updating - please use bus_type methods
> [ 16.818469] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2
> cdda tray
> [ 16.818589] Uniform CD-ROM driver Revision: 3.20
> [ 16.819228] sr 0:0:0:0: Attached scsi CD-ROM sr0
> [ 16.935327] sr 0:0:0:0: Attached scsi generic sg0 type 5
> [ 30.623122] ISO 9660 Extensions: Microsoft Joliet Level 3
> [ 30.651990] ISO 9660 Extensions: RRIP_1991A
> [ 30.753289] aufs 20080714
> [ 30.908844] loop: module loaded
> [ 31.117562] squashfs: version 3.3-CVS (2008/04/04) Phillip Lougher
> [ 58.915974] udevd version 125 started
> [ 68.898247] <6>r6040: RDC R6040 NAPI net driver,version 0.16
> (10Nov2007)
> [ 68.898269]
> [ 69.276550] input: PC Speaker as /class/input/input1
> [ 69.969743] usbcore: registered new interface driver snd-usb-audio
> [ 73.267775] natsemi dp8381x driver, version 2.1, Sept 11, 2006
> [ 73.267797] originally by Donald Becker <becker at scyld.com>
> [ 73.267809] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
> [ 73.426788] ieee80211_crypt: registered algorithm 'NULL'
> [ 75.144130] aufs test_add:336:mount[4094]: nested aufs /var/log
> [ 75.213715] aufs test_add:336:mount[4100]: nested aufs /var/tmp
> [ 77.723062] Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
> [ 81.570266] NET: Registered protocol family 10
> [ 81.573002] lo: Disabled Privacy Extensions
> [ 801.359049] usb 4-2: new high speed USB device using ehci_hcd and
> address 3
> [ 801.478598] usb 4-2: configuration #1 chosen from 1 choice
> [ 801.492847] scsi1 : SCSI emulation for USB Mass Storage devices
> [ 801.499028] usb-storage: device found at 3
> [ 801.499132] usb-storage: waiting for device to settle before scanning
> [ 806.499900] scsi 1:0:0:0: Direct-Access Flash Drive
> SM_USB20 1100 PQ: 0 ANSI: 0 CCS
> [ 806.504712] sd 1:0:0:0: [sda] 501760 512-byte hardware sectors (257
> MB)
> [ 806.506165] sd 1:0:0:0: [sda] Write Protect is off
> [ 806.506277] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
> [ 806.506369] sd 1:0:0:0: [sda] Assuming drive cache: write through
> [ 806.510859] sd 1:0:0:0: [sda] 501760 512-byte hardware sectors (257
> MB)
> [ 806.512603] sd 1:0:0:0: [sda] Write Protect is off
> [ 806.512725] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
> [ 806.512814] sd 1:0:0:0: [sda] Assuming drive cache: write through
> [ 806.512926] sda: sda1
> [ 806.529667] sd 1:0:0:0: [sda] Attached SCSI removable disk
> [ 806.530084] sd 1:0:0:0: Attached scsi generic sg1 type 0
> [ 806.531587] usb-storage: device scan complete
> [ 817.694171] usb 4-2: USB disconnect, address 3
> [ 899.694520] usb 4-2: new high speed USB device using ehci_hcd and
> address 4
> [ 899.814061] usb 4-2: configuration #1 chosen from 1 choice
> [ 899.830567] scsi2 : SCSI emulation for USB Mass Storage devices
> [ 899.845630] usb-storage: device found at 4
> [ 899.846365] usb-storage: waiting for device to settle before scanning
> [ 904.847353] scsi 2:0:0:0: Direct-Access Flash Drive
> SM_USB20 1100 PQ: 0 ANSI: 0 CCS
> [ 904.851035] sd 2:0:0:0: [sda] 501760 512-byte hardware sectors (257
> MB)
> [ 904.852432] sd 2:0:0:0: [sda] Write Protect is off
> [ 904.852600] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
> [ 904.852691] sd 2:0:0:0: [sda] Assuming drive cache: write through
> [ 904.857481] sd 2:0:0:0: [sda] 501760 512-byte hardware sectors (257
> MB)
> [ 904.859375] sd 2:0:0:0: [sda] Write Protect is off
> [ 904.859513] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
> [ 904.859638] sd 2:0:0:0: [sda] Assuming drive cache: write through
> [ 904.859756] sda: sda1
> [ 904.878172] sd 2:0:0:0: [sda] Attached SCSI removable disk
> [ 904.878588] sd 2:0:0:0: Attached scsi generic sg1 type 0
> [ 904.880110] usb-storage: device scan complete
> [ 977.851568] FAT: invalid media value (0xb9)
> [ 977.851676] VFS: Can't find a valid FAT filesystem on dev sda.
> [ 1072.369305] hda: hda1
> [ 1074.383206] hda: hda1
> [ 1166.233993] irq 14: nobody cared (try booting with the "irqpoll"
> option)
> [ 1166.234132] Pid: 4658, comm: mkfs.ext2 Not tainted
> 2.6.26-486-voyage #1
> [ 1166.234220] [<c01355ef>] __report_bad_irq+0x24/0x69
> [ 1166.234264] [<c01355f6>] __report_bad_irq+0x2b/0x69
> [ 1166.234264] [<c0135817>] note_interrupt+0x1e3/0x238
> [ 1166.234264] [<c0134f8f>] handle_IRQ_event+0x1a/0x3f
> [ 1166.234264] [<c0135e85>] handle_level_irq+0x8a/0xce
> [ 1166.234264] [<c0105252>] do_IRQ+0x4b/0x61
> [ 1166.234264] [<c0103b63>] common_interrupt+0x23/0x30
> [ 1166.234264] [<c0117f42>] __do_softirq+0x2c/0x78
> [ 1166.234264] [<c0117fb0>] do_softirq+0x22/0x26
> [ 1166.234264] [<c01180c9>] irq_exit+0x25/0x5d
> [ 1166.234264] [<c0105257>] do_IRQ+0x50/0x61
> [ 1166.234264] [<c0103b63>] common_interrupt+0x23/0x30
> [ 1166.234264] [<c01dceed>] __make_request+0x2a6/0x2d1
> [ 1166.234264] [<c01d0060>] crypto_attr_alg+0x0/0x46
> [ 1166.234264] [<c0120000>] call_usermodehelper_exec+0x10/0x98
> [ 1166.234264] [<c010fe2f>] task_tick_fair+0x3a/0x58
> [ 1166.234264] [<c01dbfa6>] generic_make_request+0x28c/0x2b9
> [ 1166.234264] [<c010fe2f>] task_tick_fair+0x3a/0x58
> [ 1166.234264] [<c0112224>] scheduler_tick+0x85/0xa5
> [ 1166.234264] [<c0139957>] mempool_alloc+0x27/0xe5
> [ 1166.234264] [<c01dc092>] submit_bio+0xbf/0xc7
> [ 1166.234264] [<c0171dfe>] bio_alloc_bioset+0x9a/0xfe
> [ 1166.234264] [<c016eb66>] submit_bh+0xbe/0xda
> [ 1166.234264] [<c0170f87>] __block_write_full_page+0x1eb/0x2b6
> [ 1166.234264] [<c0172c7e>] blkdev_get_block+0x0/0x42
> [ 1166.234264] [<c0171118>] block_write_full_page+0xc6/0xcf
> [ 1166.234264] [<c0172c7e>] blkdev_get_block+0x0/0x42
> [ 1166.234264] [<c013c52f>] __writepage+0x8/0x22
> [ 1166.234264] [<c013cc93>] write_cache_pages+0x152/0x25d
> [ 1166.234265] [<c013c527>] __writepage+0x0/0x22
> [ 1166.234265] [<c013cd9e>] generic_writepages+0x0/0x21
> [ 1166.234265] [<c013cdb8>] generic_writepages+0x1a/0x21
> [ 1166.234265] [<c013cddf>] do_writepages+0x20/0x30
> [ 1166.234265] [<c013812a>] __filemap_fdatawrite_range+0x64/0x6f
> [ 1166.234265] [<c0138318>] filemap_fdatawrite+0x12/0x16
> [ 1166.234265] [<c016df9c>] do_fsync+0x23/0x6b
> [ 1166.234265] [<c016e000>] __do_fsync+0x1c/0x2b
> [ 1166.234265] [<c0102c32>] syscall_call+0x7/0xb
> [ 1166.234265] [<c02e0000>] svc_recv+0x19c/0x6df
> [ 1166.234265] =======================
> [ 1166.234265] handlers:
> [ 1166.234265] [<d08260ff>] (ide_intr+0x0/0x1df [ide_core])
> [ 1166.234265] Disabling IRQ #14
> [ 1196.195637] hda: lost interrupt
>
>
> Thanks,
>
> Jon Trauntvein
>
> _______________________________________________
> Voyage-linux mailing list
> Voyage-linux at list.voyage.hk
> http://list.voyage.hk/mailman/listinfo/voyage-linux
More information about the Voyage-linux
mailing list