[Voyage-linux] Voyager Linux 0.6.0 and LPC-Bus

[Andrey Kaplun]

Hi,

Not work. May be need write string as firs string?

==================================================
root (hd0,0)
kernel /vmlinuz root=LABEL=ROOT_FS  console=ttyS0,38400n8
initrd /initrd.img
8250.nr_uarts=6

Error 27: Unrecognized command
==================================================

Regards,
Andrey


----- Original Message ----- 
From: "Punky Tse" <punkytse at punknix.com>
To: "Andrey Kaplun" <vectra at atsys.ru>
Cc: <voyage-linux at voyage.hk>
Sent: Sunday, January 11, 2009 5:37 PM
Subject: Re: [Voyage-linux] Voyager Linux 0.6.0 and LPC-Bus


> Hi,
>
> You can always use the specify kernel parameter in grub to override the 
> run-time settings, for example,
>
> 8250.nr_uarts=6
>
> From the time being, I will only provide a new kernel support 4 UART port 
> by default.
>
> Regards,
> Punky
>
> Andrey Kaplun wrote:
>> Need enable in kernel config next string:
>>
>> #
>> # Serial drivers
>> #
>> CONFIG_SERIAL_8250=y
>> CONFIG_SERIAL_8250_CONSOLE=y
>> CONFIG_FIX_EARLYCON_MEM=y
>> CONFIG_SERIAL_8250_PCI=y
>> CONFIG_SERIAL_8250_PNP=y
>> CONFIG_SERIAL_8250_NR_UARTS=16
>> ####################################### Because 2 serial port in ALIX2 
>> and 4 serial port in LPC-01
>> CONFIG_SERIAL_8250_RUNTIME_UARTS=6
>> #######################################
>> CONFIG_SERIAL_8250_EXTENDED=y
>> CONFIG_SERIAL_8250_MANY_PORTS=y
>> CONFIG_SERIAL_8250_FOURPORT=m
>> CONFIG_SERIAL_8250_ACCENT=m
>> CONFIG_SERIAL_8250_BOCA=m
>> # CONFIG_SERIAL_8250_EXAR_ST16C554 is not set
>> CONFIG_SERIAL_8250_HUB6=m
>> CONFIG_SERIAL_8250_SHARE_IRQ=y
>> # CONFIG_SERIAL_8250_DETECT_IRQ is not set
>> CONFIG_SERIAL_8250_RSA=y
>>
>>
>>
>> ----- Original Message ----- From: "Kim-man 'Punky' TSE" 
>> <punkytse at punknix.com>
>> To: "Andrey Kaplun" <akaplun at atsys.ru>
>> Cc: <voyage-linux at voyage.hk>
>> Sent: Friday, January 09, 2009 4:59 AM
>> Subject: Re: [Voyage-linux] Voyager Linux 0.6.0 and LPC-Bus
>>
>>
>>> Hi,
>>>
>>> If you can tell what kernel module or kernel config needed to be 
>>> enabled, I am able to add this and available to the daily build quickly.
>>>
>>> Regards,
>>> Punky
>>>
>>>
>>> Andrey Kaplun wrote:
>>>>  Hello.
>>>>  I use Voyager Linux 0.6.0 on board ALIX.2. This board have LPC-Bus and 
>>>> I want use this bus to add additional serial port to ALIX2 through the 
>>>> adapter LPC-01 by Via Technologies 
>>>> (http://www.via.com.tw/en/products/mainboards/accessories.jsp). This 
>>>> adapter used chip F81216 by Fintek.
>>>> How to me correct to tuning Linux so that in the system would appear 
>>>> new serial-ports?
>>>>  Andrey
>>>> ------------------------------------------------------------------------
>>>>
>>>>
>>>> _______________________________________________
>>>> Voyage-linux mailing list
>>>> Voyage-linux at list.voyage.hk
>>>> http://list.voyage.hk/mailman/listinfo/voyage-linux
>>>>
>>>
>>>
>>> -- 
>>> Regards,
>>> Punky
>>>
>>> Voyage Solutions (http://solution.voyage.hk)
>>> * Embedded Solutions and Systems
>>>  - Mesh Networking, Captive Portal, IP Surveillance, VoIP/PBX
>>>  - Network Engineering, Development Platform and Consultation
>>>
>>>
>>>
>>> _______________________________________________
>>> Voyage-linux mailing list
>>> Voyage-linux at list.voyage.hk
>>> http://list.voyage.hk/mailman/listinfo/voyage-linux
>>>
>>> __________ Информация NOD32 3749 (20090107) __________
>>>
>>> Это сообщение проверено Антивирусной системой NOD32.
>>> http://www.eset.com
>>>
>>>
>>
>
>
> __________ Информация NOD32 3756 (20090110) __________
>
> Это сообщение проверено Антивирусной системой NOD32.
> http://www.eset.com
>
>